Sterling Silver Tapered Petal Necklace Project

 
Tapered Petal Choker
Tapered Petal Choker Project

The next project from my class was a Tapered Petal Choker necklace.  This piece was quite a bit more challenging than the earrings, especially for my current metalsmith capabilities. 

The components for the necklace are 5 pieces of 10 gage round sterling silver wire (1-40mm piece, 2-35mm pieces, and 2-30mm pieces), 16 gage round sterling silver wire about 19″ long,  and 4 10mm glass beads.

The first step was to take the 5 pieces of 10 gage wire and make the tapered petals of the choker.  The instructor made it look so easy in his demonstration but it certainly was not as easy as it looked. 

I started with the center petal. The goal was to flatten half the lenth of the wire using a sweeping hammer motion.  This was a little trickly at first but I eventually got the hang of it.  After the first half was flattened, the petal was turned 90 degrees and the other half was flattend.  One the pice was flattened on both ends.  The piece was filed.  The instructor gave us the choice to file to a blunt straight edge or a round rounded edge.  I decided to to the rounded edge. I thought it would give it a more finished look.  After it was filed, a hole was drilled at on end to slip over the choker wire.   I finished the other four petals in the same way. 

The final step was to place the beads and tapered petal on the 16 gage wire and add a simple eye and hook on the end of the wire.

The smallest petals have the cleanest look, my rythym and technique seemed to improve as I completed the each petal.  Take a look at the blow up of the centerpiece and you can see what I am talking about.

Tapered Petal Choker Center Piece

Tapered Petal Choker Center Piece

What I learned from this project:

  • I really underestimated drilling the hole.  On the first petal I just thought I could “eyeball” the location of the hole, bad idea!  With the other petals, I used the centerpunch to mark my drill hole.  It went much better on the other petals.
  • The technique to flattend and flare metal wire (I hade tried it few times on my own but just couldn’t get it to work).
  • Use a centerpunch to mark your drilling hole.
  • How to drilling with a flex tool.

This was a really fun project, but a lot of hard work.  I have a lot of practicing to get this skill set down but I am really excited about all this.

The final projects were two sterling silver bracelets……

Advertisements

First Metal Forming Project

Metal Disc Cutter

Metal Disc Cutter from Rio Grande

Yesterday was the metal forming class at Rio Grande.  I wasn’t sure what to expect but it turned out to be a great day.  I learned so much.   The tools they have to work with their are really top notch.  There were so many tools that I wanted to bring home.  My favorites were probably the disc cutter and the jump ring making setup they have.  I would love to have both of them, my penny bank just won’t cut it.  They are both a little pricy.

Copper Earrings

Copper Earring Project

The first class project we worked on was a couple pair of earrings.  The first pair were the copper earrings.  We started with a  piece of copper sheeting and cut out discs, 2 small discs and 2 large discs.  It was then up to the student how to make the earrings.  For the smal disc I decided on a smooth finish and used the doming block for it’s shape.  The larger discs I used a ballpen hammer to texture the disc.  I had never used a flex tool so that was a bit of a challenge in the beginning.  

The lesssons I learned on this project:

  • Always measure the location of the drill holes.  One of the larger domes had the drill hole too low and the the discs overlap.
  • Texture, drill and then shape a piece of metal.  On this pair I drilled first and after I textured, the drill holes were almost completely closed from stretching the metal.  I had to redrill the holes.
Sterling Silver Earrings

Sterling Silver Earring Project

The next pair of earrings were sterling silver earrings.  For this project the shapes were precut for everyone in the class.  We were given a round sterling disc and a somewhat rectangular shape sterling piece. 

On the disc I ran the disc through a metal corrugater.  This was kind of a cool tool too.  You place a piece of metal through two corrugated wheels and depending on the amount of tension  on the wheel will contol how deep the corrugated impressions are.  The disc was then placed in the domer for it’s shape.  On the relangular pieces  I used a goldsmith hammer to get the texture on the metal.

Both of these projects were great to get started with the metal forming.

The next project was a sterling silver petal choker, I’ll tell you all about it next time…..

Metal Forming Class

Rio Grande Jewlery Suply

I know it has been so long since I have posted.  First I was busy getting ready for the Artfire Christmas in July sale, then I have been doing daily maintenance for the sale for the past couple of weeks.  The sale runs until Friday, July 23.  Hope you get a chance to stop by.

Now onto today’s post.  For sometime now, I have been wanting to continue learning some new techniques with my jewelry making.  The metalsmithing and metal forging really intrique me .   I have read a lot of books but there is nothing like hands on instruction.  I found a one day workshop at one of the local jewelry supply businesses here in town. I just registered for their metal forming class in August and I am so excited.  Here is a brief synopsis of the class:

Make a sterling silver neckband, bracelet and domed earrings while learning to form wire and sheet into wearable jewelry. Students learn to use professional jeweler’s tools while working at a jeweler’s bench.

Here are the projects that we will work on.  I will post pictures of my actual projects once I have finished the class.  Until next time, have a great evening.

Class Projects

%d bloggers like this: